E
Reaction score
40

Joined
Last seen

Latest activity Postings Images About

    • E
      emedlin replied to the thread P0340 / P0344 and limp mode.
      I installed the new connector. My wire connection is in the thick part down near the 'T' intersection. I zipped tied the connector to...
      • 1738897830833.png
      • 1738898076759.png
    • E
      emedlin replied to the thread P0340 / P0344 and limp mode.
      I don't think it is the crank sensor. I am pretty sure it is the actual connector for the cam sensor. It did it again about an hour...
    • E
      emedlin replied to the thread P0340 / P0344 and limp mode.
      P0344 came back today and put it in limp mode again. Wish I knew how it was losing the signal. Any chance it could be the crank...
    • E
      emedlin replied to the thread P0340 / P0344 and limp mode.
      I thought it was around that. It must just show one when it loses the signal. So, I put the NAPA sensor back in and drove it around...
    • E
      emedlin replied to the thread P0340 / P0344 and limp mode.
      Seems to be doing it pretty regularly right now. I used the ThinkDiag to record it when it happend. I had all the cam and crank data...
      • 1738104615375.png
      • 1738105287781.png
    • E
      emedlin replied to the thread P0340 / P0344 and limp mode.
      It threw a P0344 again this afternoon and went into limp mode. Looking for something else to try now? Should I try the NAPA sensor...
    • E
      emedlin replied to the thread P0340 / P0344 and limp mode.
      It runs fine now and no codes, currently. We will see how it does after a few weeks. Interesting thing I found out. So, when I took...
    • E
      emedlin replied to the thread P0340 / P0344 and limp mode.
      Got my Thinkdiag2 today. I adjusted the OPDA to 0.5 after tightening it it down. The strange think is it will not do a relearn. I...
    • E
      emedlin replied to the thread P0340 / P0344 and limp mode.
      I ordered the Thinkdiag2, as the shop isn't open today. And, it was only $120. It will be here tomorrow. I did find out it you can...
    • E
      emedlin replied to the thread P0340 / P0344 and limp mode.
      Found a thread where this one was mentioned...
    • E
      emedlin reacted to JKP's post in the thread P0340 / P0344 and limp mode with Like Like.
      I don't know of any of the cheaper ones that can do it. There's a thread somewhere on the ones that can. I didn't do a reset until...
    • E
      emedlin replied to the thread P0340 / P0344 and limp mode.
      I didn't think it looked to bad. But, I have only seen some pictures on here and some looked way wores. I used my borescope to take...
    • E
      emedlin replied to the thread P0340 / P0344 and limp mode.
      That is what I just did before I came back in and read this. :LOL: It runs now. Still got a P0116, but I think I am done. I am...
    • E
      emedlin replied to the thread P0340 / P0344 and limp mode.
      See the video above of the old one. The new one didn't really move at all. New problem. I loosened the OPDA and move it a little...
    • E
      emedlin replied to the thread P0340 / P0344 and limp mode.
      Play in old OPDA. The new Crown barely moves up and down at all. Wear on old OPDA and camshaft.
      • 1737767101326.png
      • 1737767118743.png
  • Loading…
  • Loading…
  • Loading…