Marklar1983

Supporting Member

Average Joe 40 From Sparks, NV

Joined: Apr 11, 2022

Last seen: Yesterday at 10:35 AM

Latest activity Postings Images About

- Marklar1983 reacted to leoang90's post in the thread What did you do to your TJ today? with Like.
  
  Fashioned a tailgate stop out of a (low cost) door stopper. My tailgate now stays fully open even when I'm parked on a slope!
  
  Yesterday at 10:35 AM
- Marklar1983 replied to the thread What did you do to your TJ today?.
  
  Installed a set of Bosch 4-hole injectors from Precision Auto Injectors.
  
  Tuesday at 9:47 PM
- Marklar1983 reacted to mjonesjr84's post in the thread What did you do to your TJ today? with Like.
  
  After reading this, if you were closer than the other side of the country, I'd grab a bottle of bourbon and head your way. Beer isn't...
  
  Tuesday at 9:46 PM
- Marklar1983 reacted to Harold&Cat's post in the thread What did you do to your TJ today? with Like.
  
  New 4.88 gears and 2 inches of lift taught me that my 20 year old front driveshaft is worn out . The minor vibrations turned into major...
  
  Tuesday at 9:45 PM
- Marklar1983 reacted to red02tj's post in the thread What did you do to your TJ today? with Love.
  
  First top down ride of the season.
  
  Tuesday at 9:44 PM
- Marklar1983 replied to the thread Do-anything LJ build advice.
  
  Took a break from setting up gears to install a set of Bosch 4-hole injectors from Precision Auto Injectors.
  
  Tuesday at 9:43 PM
- Marklar1983 reacted to hosejockey61's post in the thread Do-anything LJ build advice with Like.
  
  That's the place I'm talking about, do it to both sides. I usually wait until I'm doing final install as they can catch the shims going...
  
  Monday at 2:52 PM
- Marklar1983 replied to the thread Do-anything LJ build advice.
  
  I cut a drain on the left (ring gear) side; I think the right already has a channel. I’ll check tonite. Rear Dana 44, didn’t mention that above.
  
  Monday at 2:51 PM
- Marklar1983 reacted to hosejockey61's post in the thread Do-anything LJ build advice with Like.
  
  Just make sure the bearing race seats are clean when you drive them in. Also, didn't forget to cut an oil return slot on the right side...
  
  Monday at 2:47 PM
- Marklar1983 reacted to hosejockey61's post in the thread Do-anything LJ build advice with Like.
  
  The seal housing is on the left (ring gear side) as you're looking at it. The bearings get pressed on first with no shims. The seal...
  
  Monday at 2:44 PM
- Marklar1983 replied to the thread Do-anything LJ build advice.
  
  That’s the clarity I needed, thanks!
  
  Monday at 2:44 PM
- Marklar1983 replied to the thread Do-anything LJ build advice.
  
  @hosejockey61, this is my first ARB install. Do I put the carrier shims between the seal housing and bearing cup, or between the seal...
  
  Monday at 1:21 PM
- Marklar1983 reacted to hosejockey61's post in the thread Dana 44 carrier shims with Like.
  
  ARB's use their own master shims. They measure right at 100. Did your ARB not come with two of them? It should have. They are the same...
  
  Monday at 1:17 PM
- Marklar1983 reacted to AirborneTexasRanger's post in the thread All things welding with Like.
  
  Spatter/Buck Shot/BBs, whatever you wanna call it will tell you a lot about how you're welding. The two most common causes of spatter...
  
  Apr 11, 2024
- Marklar1983 reacted to CharlesHS's post in the thread Bartact woes with Face Palm.
  
  Shifting jobs out of the USA needs to stop. That is only a small part of why our economy is in the state it is... I am hoping our...
  
  Apr 11, 2024
Show older items
Loading…
Loading…
Loading…

Top Bottom

Back

Search

Search

Marklar1983

Find content

Latest activity Postings Images About