Latest activity Postings Images About
-
-
Shawn at Tom Wood's reacted to 97TJNM's post in the thread The lights before lockers build: double tough 97 Sport with
Like.
@Shawn at Tom Wood's Funniest sticker in the industry, right here. I'm not normally one for dick jokes just for the sake of being... -
Shawn at Tom Wood's replied to the thread The lights before lockers build: double tough 97 Sport.Neither am I actually. I used to roll my eyes at the my shaft's a woody slogan a bit. Maybe it feels more refined now that we've had a...
-
Shawn at Tom Wood's reacted to 97TJNM's post in the thread The lights before lockers build: double tough 97 Sport with Love.
Well, after dialing everything in today, I rechecked everything, and my carefully measured front driveshaft length of 37.5 inches...
-
Shawn at Tom Wood's reacted to R3ID05TJ's post in the thread 2005 Rocky Mountain Edition with 53,000 miles with Like.
Excellent. Ordering now. Thank you for the top notch customer service.
-
Shawn at Tom Wood's reacted to JMT's post in the thread 2005 Rocky Mountain Edition with 53,000 miles with Like.
Just call Tom Wood. They’ll be able to guide you. Better yet… Calling @Shawn at Tom Wood's. Read this post and the couple above. You’ll...
-
Shawn at Tom Wood's replied to the thread 2005 Rocky Mountain Edition with 53,000 miles.Yes. By the way, there is some room for error with all of this. I am confident that this process will result in a perfect fit but if it...
-
Shawn at Tom Wood's reacted to R3ID05TJ's post in the thread 2005 Rocky Mountain Edition with 53,000 miles with Like.
Bingo that answers my question. So I go outside and measure vehicle right now and add 1/8" to the measurement. Then I'll go ahead and...
-
Shawn at Tom Wood's replied to the thread 2005 Rocky Mountain Edition with 53,000 miles.Assuming you ordered that with the 1310 series yoke option you'd add that 3.125" back into the subtracted length. Or a maybe less...
-
Shawn at Tom Wood's replied to the thread 2005 Rocky Mountain Edition with 53,000 miles.You don't need to install the SYE first. You can measure the Jeep the way things are now and order the SYE and drive shaft all at once...
-
-
Shawn at Tom Wood's replied to the thread SYE yoke bolts are too long.You know why I like participating on forums? Because I like to be able to cut through the noise and settle disputes about things from a...
-
-
Shawn at Tom Wood's replied to the thread The Official Tummy Tuck FAQ Thread.You are absolutely right, by definition the wheel travel on one side is actually dependent on the other side. For one side to go down to...
-
Shawn at Tom Wood's reacted to Chris G's post in the thread 03 Rubi rear driveshaft rebuild question with Like.
Thanks so much for the excellent explanation. I was just dumbfounded as the yoke didn’t appear damaged in any way and I couldn’t imagine...
-
Shawn at Tom Wood's replied to the thread 03 Rubi rear driveshaft rebuild question.The one at the axle end of the shaft should be a conversion joint, it's 1330 series in one direction and 3R series in the other. The...
-
Shawn at Tom Wood's replied to the thread Axle bind at full droop.We may be (we are) venturing outside of my realm of expertise but I think this would apply to almost any suspension setup, even leaf...
-
Shawn at Tom Wood's reacted to pagrey's post in the thread The Official Tummy Tuck FAQ Thread with Like.
Ah, that makes good sense. If you do need them to keep the shaft in you don't have to limit flex. Thanks.
-
-
Loading…
-
Loading…
-
Loading…
