Search results

  1. L

    Corbeau Trailcat with flip seat install and review

    Can you get them lower? I have a 97 and I’m 6’4”
  2. L

    Warn hub conversion resource

    I'm looking for 2 rotors for my current warn 5x5.5 kit. Lmk. Pm me!
  3. L

    Ford 8.8 Axle Swap Info / FAQ

    What's everyone run for a track bar? Bought a iron Rock and it's too thick for what ever swap mount I have in the jeep I just got. It has a track back now with a heim kinda thin brackets.
  4. L

    Manual hub conversion

    Wow thank you.
  5. L

    Warn hub conversion resource

    The WU-08 is for the 5x5.5 do I need to do any boring? Sorry I'm still learning this kit.
  6. L

    Manual hub conversion

    I have had no luck besides this but not sure if this is correct. Is the 4.5 and 5.5 parts list the same ? If you scroll down they do a manual swap. Thanks https://jeepspecs.com/tj-generation/u-joint-grease/
  7. L

    Manual hub conversion

    Any idea where to start on to find where to get these seals washers and bearings?
  8. L

    Manual hub conversion

    The steering I tracked down. It is OffRoadOnly U-turn. Just sourced the drag link ends and tie rod ends. Would be great if some one knew. Thanks
  9. L

    Manual hub conversion

    Hey all. Recently purchased a 97 TJ with a 04? Idk LP Dana 44 with factory locker. Anyways it has a manual hub conversion with warn premium lock outs. Any idea what kit this thing has in it? I would like to get the seals and bearings in order to replace the ball joints and new rotors. Much...
  10. L

    Does a cold air intake add power on a 4.0?

    Inbox me so I don't forget and iff I get a replacement stock I'll ship this to you for cost of shipping to hahah
  11. L

    Does a cold air intake add power on a 4.0?

    Absolutely if it's in good working condition I'll take it lmk. Inbox me when you can. I have PayPal.
  12. L

    Does a cold air intake add power on a 4.0?

    I recently bought a 1997 Jeep Wrangler it has an air raid cold air intake on it. It's pathetic looking it's a metal tube in a hot engine bay with a filter that is sucking hot air and then the tube is absorbing all the heat. Nevertheless it's annoying when I step on the gas and randomly when the...
  13. L

    Pinion Angle and Driveshaft

    Thank you sir. This is what I was looking for lol. Yea got the jeep from a older gentleman, son built it then moved on. It has Radius Uppers and long arm lowers front and rear with the 8.8. So remove the shaft and check for how far it's engaged? I had thought clicked post reply. When spraying...
  14. L

    Pinion Angle and Driveshaft

    Thank you for all the replays loaded with information. The vibe I am getting is a bassy vibration, I'll pull the shaft and check the ujoints.
  15. L

    Pinion Angle and Driveshaft

    Hello all. I have a 97 TJ with I'm guessing a 4-6" long arm lift. I'm getting a vibe on the highway around 3k rpm at 70 its low frequency vibe. I only noticed it after I installed my new to me used hard top. I measured my opinion angle and Driveshaft but I'm not sure what I should have for...
  16. L

    8.8 rear end seals (again)

    No burs in the shaft ? What does the seal look like now ?
  17. L

    Magnum engine questions

    98' 5.9 grands are pretty cheap these days. Got mine for 1200 bux and it needed a trans. To swap that drivetrain in my tj would be ridiculous, the low end torque of the 5.9 geared properly can be great on the trails. Probably better fuel mileage than the 4.0.
  18. L

    What are these called?

    I just did my valve cover last night and have them if you need them. Didn't use them with the new valve cover.
  19. L

    Hey all new here

    thank you sir, been on a few forums over the years to help others and learn more myself. my SO has a JK on 40's the jeep has lots of engine issues. I came from a 2017 Tacoma and that too!! problem child. always had good luck with te 4.0 and RH
  20. L

    Hey all new here

    double post sorry