Search results

  1. smithcaz

    New York Dana 30 and Dana 44 stock axle shafts

    I can look into it, I think it will cost a bunch but can let you know. Give me a couple of days to get it together.
  2. smithcaz

    Novita EP26 LED Turn Signal Flasher Relay

    I did the JK turn signal mod in the grill because of the flat fenders.
  3. smithcaz

    Novita EP26 LED Turn Signal Flasher Relay

    I have a flasher relay for those of you that are switching to LED turn signals. I went back to standard bulbs and pulled this. It is a Novita EP26. $10 shipped to Continental USA.
  4. smithcaz

    Crown OPDA, new

    I have a Crown OPDA that I had as an on-hand spare. Never put it in, just sat in a box of parts. Looking for $80 shipped to Continental USA.
  5. smithcaz

    New York Dana 30 and Dana 44 stock axle shafts

    I have my old stock axle shafts from a Dana 30 and Dana 44. The Dana 30 u-joints are a little loose and the Dana 44 bearings have been compromised by spider gears falling apart. You could replace the u-joints and replace the bearings and have a good set of axles or spray out the bearings and...
  6. smithcaz

    New York Setup Bearings Shims Misc - Dana 30 Dana 44

    I have my setup bearings (Timken) that I made for my Dana 44 / Dana 30 rebuild. You can see in the pictures what bearings and races that are included. Some are tighter and some are looser than others, they worked for me though. Also included are two new bearings, a bunch of assorted shims, 2...
  7. smithcaz

    Body Lift - One Inch

    I have a body lift for sale that was taken off my Jeep. It appears to be a Daystar or a copy. It should be a 1.25 inch body lift I think but some of the pucks have been compressed to less than that so call it a 1 inch + body lift. What you see in the picture is what you will get. One of the...
  8. smithcaz

    Anyone have pictures of their TJ with 35's on a 4 inch lift?

    4.5” springs up front and 3.5” springs in the back with 35” tires.
  9. smithcaz

    New to me 06 and a turn signal/marker light question

    Yes, LED like this one: https://www.etrailer.com/Trailer-Lights/Optronics/MCL13A2B.html There are three wires in the original setup, I cannot remember what they are but one of the wires is white with a stripe that is different on the driver's side and passenger's side, those are the wires I...
  10. smithcaz

    New to me 06 and a turn signal/marker light question

    Here is a pic of my setup. The marker light is attached to a piece of aluminum with a 90 degree bend in it. It is held to the fender by the bolts that hold the hood latches.
  11. smithcaz

    New to me 06 and a turn signal/marker light question

    The side marker lights do not work exactly as factory unless you get a LED light with three wires made for that type of application. When using a two wire LED you can wire it so when the lights are off the LED marker will be off (like stock) and the turn signal works normally. When the lights...
  12. smithcaz

    New to me 06 and a turn signal/marker light question

    The LED marker lights will be fine as long as you keep the incandescent turn signal bulbs. I have the same setup on my Jeep.
  13. smithcaz

    Need help building auxiliary fuse box

    1. Relays handle the high load and allow the switch wiring to be smaller gauge. 2. There will be power going to the relays but the circuit is not crated until the switch is thrown. 3. I don't know of any guides, I just bought one of those 6 position relay panels that you build yourself from...
  14. smithcaz

    Huge oil consumption, any idea before testing?

    Thanks for the info, I ordered a new valve and grommets, I cannot imagine that being the total cause of the oil consumption but it cannot hurt to swap it.
  15. smithcaz

    Huge oil consumption, any idea before testing?

    4.0L with 99,000 miles on it. The engine is using about 1 quart every 200 miles. I have not done a compression test or leak down test yet, have not had the time to do either at this point. If the Jeep is parked, there will be no oil on the ground. When the Jeep is started there is no cloud of...
  16. smithcaz

    Milestar Patagonias or BF Goodrich KO2?

    I have the Patagonia MT tires. They are louder than a street tire obviously but behave well. Once you get offroad they grip. In my yard they will pull up the grass while turning as opposed to flattening the grass. This would happen with any MT tire but you are asking about two specific tires. I...
  17. smithcaz

    What is this?

    That is the satellite antenna.
  18. smithcaz

    What tools do I need to remove my body lift?

    Take a look at the wire harness at the back of the engine next to the firewall. To remove the body lift you have to raise the body and the wires may already be stretched tight.
  19. smithcaz

    Big Long Plastic Coil Holding Thing in my Freaking Way

    Once you move the red locking clip, there is a tab that you need to squeeze. I found that if I use one hand to squeeze the tab and wiggle the connector it will come off or move enough to hold the tab in the release position. I can then use a long flat screwdriver to push it off the rail. Watch...
  20. smithcaz

    Dana 30 HP & LP gear swap: stock or upgraded shafts?

    My Yukon front shafts have 4340 in the yoke section.