Search results

I have a flasher relay for those of you that are switching to LED turn signals. I went back to standard bulbs and pulled this. It is a Novita EP26. $10 shipped to Continental USA.

I have a Crown OPDA that I had as an on-hand spare. Never put it in, just sat in a box of parts. Looking for $80 shipped to Continental USA.

I have my old stock axle shafts from a Dana 30 and Dana 44. The Dana 30 u-joints are a little loose and the Dana 44 bearings have been compromised by spider gears falling apart. You could replace the u-joints and replace the bearings and have a good set of axles or spray out the bearings and...

I have my setup bearings (Timken) that I made for my Dana 44 / Dana 30 rebuild. You can see in the pictures what bearings and races that are included. Some are tighter and some are looser than others, they worked for me though. Also included are two new bearings, a bunch of assorted shims, 2...

I have a body lift for sale that was taken off my Jeep. It appears to be a Daystar or a copy. It should be a 1.25 inch body lift I think but some of the pucks have been compressed to less than that so call it a 1 inch + body lift. What you see in the picture is what you will get. One of the...

4.0L with 99,000 miles on it. The engine is using about 1 quart every 200 miles. I have not done a compression test or leak down test yet, have not had the time to do either at this point. If the Jeep is parked, there will be no oil on the ground. When the Jeep is started there is no cloud of...

After rebuilding my Dana 30 and Dana 44 due to unexpected circumstances, I thought I would write down a few thoughts post-completion. It all started when I changed my gear oil in the 44 and found a set of spider gears looking like they had seen better days a long time ago. I searched for a...

I just finished rebuilding my axles and am going through the break in process. After a 6 mile drive I parked the Jeep and the rear diff cover near the bottom is 143 degrees and the pinion I see 181 degrees. The front diff cover near the bottom is 100 degrees and I forgot to measure near the...

When setting up new gear with new bearings on a Dana 44 I see two ranges for new bearings, one is 14-19 inch pounds and the other is 20-40 inch pounds. Which is the correct range?

I may be looking for a set of spider gears for a non-rubicon rear Dana 44. Anyone have a set laying around after a locker install?

My driveshaft bit the dust and I am ordering a replacement now, I have a measurement from yoke to yoke of 15.5 inches. I am being told that the driveshaft for this lift is normally 16.25 to 16.5 inches long. Anyone out there with a similar build that can do a quick measurement of their...

I am looking for a pair of front turn signal sockets and the harness/pigtail that plugs into the socket. Previous owner cut them off so I am left with just the wire and I want to put the JK turn signal lens into my grill and get rid of the 3/4" LED bulbs in the fenders. Let me know if you have...

I am looking for one switch filler blank. Trying to decide which way to wire some things up but need one more blank to give option 2 a chance. If anyone has one blank laying around they want to sell, let me know how much you want for it. Thanks Found on Quadratec for $3.49 each currently...

I have a switch panel for the 97-02 TJ. I had this for a project but will not be using it in my 06. As you can see in the picture there is the 12V socket, no blanks and one fog light switch. The fog light switch is an unknown. I do not know what year it is from, I do not have the pigtail for it...

I am looking for the small cover on the right side of the steering wheel for a 2006 TJ. Any of you that added cruise control would have one of these covers. Let me know if you have one and what you want for it. Thanks

I have not taken anything apart at this point so it may be super easy but I doubt it. Does anyone know of a way to identify the axle shafts without physically taking them out and hoping there is a big label stuck on them with all the information you would ever want to know? Are there some...