Search results

I have had an issue for a while now with a broken retaining clip. Tried the local Napa etcetera and there universal clips are the wrong size. Does anyone know where you can get a decent replacement for a reasonable price instead of the $14-$25 I have seen online for what really is less than...

So I have run into a new electrical issue. Occasionally when turning right it rapidly flashes like it has a damaged bulb but only for 3-4 flashes then returns to the normal flashing. I went through everything today there are no obviously damaged bulbs and the sockets seem in good shape. Cleaned...

I own 1998 that I picked several years ago and have done quite a bit of work on, including adding factory AC, cruise, intermittent wipers and so on. a couple of months back my clockspring started giving me grief I bought a new one and replaced it , a Dorman unit. everything seems good. 2 weeks...

Silver paint can be a challenge, a lot of painters will do a mist coat to avoid tiger stripes or mottling of the paint. If you google spray painting silver paint and how to avoid tiger stripes you will find a lot of information that will help you. You will need to sand back lightly to the base...

Besides checking and cleaning all the wiring connections check the actuator behind the key cylinder make sure the center section is in tact and not starting to fail, it is possible it is the starter itself. I have a manual but the starter was slow and at times would just click and not start the...

The difference in wiring in the steering wheel is simply having a clock spring with the through wires for cruise or not. At the time of production if they pulled a clock spring that was wired for cruise and installed it, it would work for the horn and airbag but the cruise wires would be just...

So I just did this on my Jeep about a month ago. I replaced the actuator and ignition switch plus upgraded to delay wipers while in there. I was having a issue where you would hear a click but it would not start the first 2-3 times I tried the key and then it would turn over, not great but...

When I did the cruise install on my 98 there was another forum I was on that had a guy trying to do the factory cruise on a 97. One of the posters to that forum mentioned he had bought a new sport off a lot in June or July of 97 and cruise was not an option at that point. At a later point they...

I recently replaced my starter because the brushes were worn out. The new starter worked fine for about 3 weeks then started having an issue where it would not start just a weak click when you turned the key to start. That would happen 2-4 times and then it would turn over and start. After...

So this plug the Brown/Yellow wire become a Red/black wire and the Red/Yellow (should be light green trace becomes a Red wire correct? If the the answer is yes and these are the same wires in this next picture then you have a issue with the temp sensor. The colors are not random they are there...

Follow the wiring schematic you need wires that go from one point to another so yes the harness you installed will work as long as make the connections as I outlined.

Not in this case resistance matters it's a 5 volt can bus systems if it sees the incorrect change in the voltage it turns on/ off other things it aligns with a specified voltage or nothing happens at all if there is no specified voltage in the range. And normally I would agree with you. I was a...

Not in this case if you check each of those year specify a different resistance value. And will not work in other years. I know this from personal experience as the first set I bought were for 99-2002 and did not work. Under normal circumstances a suffix change would be and up dated part. I...

Don't cut the temperature sensor wires leave the new temp sensor and pigtail intact as a spare make your cut on the harness side like 3-4 inches past the plug. Then splice those wires into the existing harness. Just make sure you splice the right wire to the right wire it helps to lay the new...

There is actually more numbers then that, they break down into four differing sets and at the core of first three sets it is actually just the small resistors on the inside that are different but the wrong resistance resistor in a vehicle means the system will not function. Here is the full...

Sorry it was a long day yesterday and I missed those are the two new ones but if you don't read the first line of my last text completely literally you do infact have both a new temp sensor and the original one in the Jeep you just can not see the original one. Follow the rest of what I typed to...

The airbag is easily disarmed. Disconnect the battery and leave the vehicle alone for 5-10 minutes. After that you can disassemble the steering wheel. The switches are easy to get to the clock spring is actually behind the wheel which you not not need to remove to test the switches. The clock...

I installed cruise control on my 1998 that did not have it. there were two thing that threw me off for a minute and both of them would cause the issue you have and so could several others. First the button for on/off (the second set because the first set was misrepresented and was actually for a...

in this image you have the original and the bought battery sensor plugs. your not adding a second sensor. You only need one and it is there so use the one that was originally in your jeep keep the original wiring and just add the wire that goes to the clockspring. you need a jumper from the...

I was referring to this photo from Tycarver. There should be no splice to the Red/light green wire from the clock spring it goes directly to the PCM pin C32. There is a second wire attached to the Brown/yellow wire that is Black/red If that wire goes to the plug show in the second photo and...