Search results

Is the 24volt guy still making switches for jeeps? If not does anyone know another source for something similar?

Pulled the throttle body this morning and gave it a good cleaning, removed the IAC and cleaned that as well. Put everything back together with a new throttle body gasket, fir it up and it's idling at 2000rpm. Took it for a few mile drive thinking maybe it just needed to run a bit and there's...

So I have the issue where I only have flow from the floor and defrost vents. I assumed it was a vaccum leak (even though the cruise control operates normally which I thought it wouldn't with a vaccum leak) and replaced the engine bay vac lines with a Mopar replacement. No change. With the...

Installing a new front pinion seal and notice the new one (masterpro part #5778) is not flanged like the original. Is this still okay to use?

Had an issue a few weeks ago where I lost a rear drive shaft. When it went it punched a hole in the muffler. I bought a banks to replace it and am wondering if it's possible to do without removing the skid plate.

U joint gave out and lost my rear driveshaft. I have a new driveshaft but the u joint retaing bolts at the rear diff sheared off and I'm not confident I can ez out them loose. Can I remove/replace the u joint carrier at the rear diff? In the middle of moving and could use some advice in a...

U joint went out and lost my rear drive shaft. Bought a new drive shaft but when it went it sheared off the u joint retaining bolts at the rear u joint (rear diff). I'm not sure I'll be able to EZ out the broken bolts. What are my options? Can I just unbolt the diff side of the u joint mount...

Looking at adding a kinetic rope for offloading, what size and length is right for a 2dr TJ?

What gauge/fitting set do you use for testing vaccum pressure? The ones I see are for fuel pumps and the adapters are all too large.

Does anyone know if 12v guy is still in business? If not are there alternative sources for a winch panel?

On the side of the road. Fan clutch went out allowing fan to "wobble" like it had a busted bearing. Smacked the shroud busting it into pieces. Got a new fan clutch and replaced. Made it 10 miles down the road and it's overheating, no power in 5th gear (can't maintain speed) and battery is...

2006 TJ X, 6 speed manual. Replaced a cracked radiator with the Mopar replacement and after recounting the shroud onto the factory holes on the radiator the shroud sits about 1 inch, the fan blades make contact at the bottom of the shroud. Anyone else ever had it happen? I'm off to buy a new...

Good morning, My 06 TJ has a smittybilt soft top. No idea if the frame is factory or smittybilt. My question is if a bestop replacement top (fabric only) will fit over the existing frame?

Does anyone know if it's possible to get replacement smittybilt vinyl windows for an 06.

2006 4.0 135k So, a while back I changed out my clutch and also my clutch master and slave. Since then the jeep will not start with the clutch depressed. I have to push the clutch in, let it out. Make sure I'm in neutral and have the brake pedal depressed in order to start it. It won't even...

Hey guys, accumulator has developed a pretty good leak, I've never replaced one before. Is it much of a project? Any tips?

Finished reinstalling transmission after replacing TOB and clutch. After all is said and done the clutch pedal goes all the way the floor without resistance. It returns when you let off. Ideas?

Finishing up re-installation of my transmission and have one electrical connector that for the life of me I can't figure out where it goes. It splits off the wire harness just about where the bell housing meets the transmission. Looks like this. Please point this fool in the right direction

I stalling a new clutch, carrier bearing and pilot bearing. Drive the pilot bearing out with a mix of Grease and bread but the pilot bearing came with the carrier/bushing. The bushing has a beveled edge on one side. Just looking to confirm if the beveled edge goes out towards the bell housing...

does anyone know the correct speedo gear for 265 75/16's? I'm off about 8 mph. 2006 4.0 6sp. Thanks