Search results

  1. XCRN

    Bumper Rust Prevention

    So I am looking for ways to minimize rust building up on things like bumpers, tire carriers, axles etc. This is about a year of having this sand blasted entirely and coated with primer and bed liner. I am probably going to see about having all this stuff stripped again and redo it, but I was...
  2. XCRN

    Fox Shocks Stem to Eyelet

    I ended up with a new set of front adjustable Fox reservoir shocks for a TJ for a great deal. However the compressed length is too long for my front setup, so I was thinking I could use these with an outboard job on the rear. Since the top stem of these shocks thread into the body I was...
  3. XCRN

    Trackbar to Diff Interference

    So I just found my Core4x4 Trackbar is interfering with the stock diff cover on my TJ at 1in from full compression and I cannot adjust the control arms enough to keep it from interfering. If I had the time I would probably just get one of those double shear mounts and relocate it further...
  4. XCRN

    Rubi Locker in Non Rubi Housing

    I have a set of Rubicon axles with lockers. The problem is rear has all the brackets stripped, and I was gonna use that housing for a custom job (coilovers and other goodies) since half the work was done for me. But I want to put a set of Rubi axles with the lockers into my LJ that will...
  5. XCRN

    03-06 Radio Bezel On 2000

    I bought a touch screen radio like I have on my LJ that fits in Chrysler single DIN spots to put onto my 2000 TJ. I just found out that I cannot just swap the newer 03-06 bezel on. Apparently there is a lot more that changes like the HVAC controls and the radio are spaced differently. What...
  6. XCRN

    Rubicon Gears

    So I just got a set of Rubi Dana 44 axles for the price of a single regular Dana 44 axle and super excited to get the set under my TJ, however I do not want to run 4:10 but something numerically lower because V8. I saw a little bit of info saying the Rubicons use thick cut 4.10 gears, so does that mean...
  7. XCRN

    AX15 Input Shaft Repair

    So pilot bearing took out the input shaft on my AX15 from my install mess up. Looks like where the pilot bearing goes it wore down that part of the shaft. Before I start the process of replacing the input shaft on my AX15, is there a way to repair the tip without stripping down the trans? I...
  8. XCRN

    More Clutch Issues

    So after driving a few months from fixing my last clutch issue where I could not shift which turned out to be the fork came loose, I can no longer shift again. The fork is not loose at-least from what I can tell without dropping the trans (last time it was very apparent with the slave cylinder...
  9. XCRN

    Shock Upper Stem Mount Pivot Limits

    Just bought a pair of new front Fox reservoir shocks that are longer than what my setup would call for (because it was a great deal) but I am looking at lowering the lower shock mount by cutting the perch and welding tabs to the control arm brackets. However this would offset the lower eyelet...
  10. XCRN

    Bump Stop Misalignment

    How much bump stop misalignment is too much? I am showing about 1” offset. I think its mostly the necessary pinion adjustment for a double cardan drive shaft is whats doing it. Ill add the plans to move the perch later but I cannot do it right now. Would this be okay even playing in the...
  11. XCRN

    Center Console Front Half Interchange

    Are the front halfs of center consoles interchangeable from different years? I have an earlier sub console and want to install an 05-06 front half since the shifter cutout is further forward and lines up better with my engine swap and I am currently using an 05-06 tunnel cover. I just want to...
  12. XCRN

    WTB: AX15 Short Throw Shifter

    I am looking for an AX15 short throw shifter like the B&M. Either around Dayton OH or be willing to ship. Paypal ready if needed, thanks.
  13. XCRN

    Possible Bent Clutch Release Arm

    So I am having an issue shifting gears. I went from difficult to shift gears all of the sudden to not being able to shift gears at all with the engine running. I can shift fine if the transfercase is in N with engine running, or shift while engine is off. The clutch, TOB, release arm, and...
  14. XCRN

    How To LS Swap Your TJ

    Will add pictures, typed this on my computer and all my photos are on my phone so ill go back and edit them in. I will also be adding info as subjects come up and I do more of these. So you want to go to the dark side discombobulate your TJ and throw a LS motor in your rig? Well its not that...
  15. XCRN

    LJ Adventure Build

    So I just bought me a Red LJ to go with the 3 Green TJs. I have been wanting something a bit bigger for me and my significant other to go on longer adventures with like exploring the public trails out West, going as far North as I can in Canada and other trips. I found this LJ for cheap...
  16. XCRN

    Ohio TJ Parts

    I have a bunch of random TJ parts I am selling. Willing to ship most of the small stuff. Willing to cut deals on multiple items. Stock control arm set, $100 OBO. Bushings are Moog and about 2 years old. Sway bar with bushing and links, $50 OBO. Links and bushings are Moog, about 2 years...
  17. XCRN

    LJ Frame Repair

    So I am looking at buying a flame red LJ that needs frame repair. These are the pics I got. Looking at the frame repair kits it looks like it would not fix it entirely with how much rust goes up into where the body mount bracket is. Seems like all the kits weld to the clean metal around the...
  18. XCRN

    Hitch Interference With Genright Fuel Tank

    My Curt trailer hitch that I had with stock fuel tank will not fit with the genright 24.5 tank that should fit like factory. The skid plate is about 1/2” too wide. Any suggestions or is there another trailer hitch I could purchase that would fit?
  19. XCRN

    Removing Genright Fuel Tank From Skid

    Is there a way to separate the Genright TJ 24.5 gallon fuel tank from the skid plate? It seems like the front passenger side mount interferes but not sure if there is a trick to this or not. I am wanting to refinish the skid plate.
  20. XCRN

    NP231J Chain Slack

    Does these seem like too much chain slack? When pulled up it hits the shift fork tower, when pulled down it does not hit case. I looked up a few videos about chain slack, they said if the input shaft was locked in place and you can turn the front output 1/4 turn while in 4wd its too loose but...