Search results

https://www.facebook.com/marketplace/item/346673915042328/

Jeep is an 04 with the 4.0. I replaced my 02 sensors about 2 years ago. Since about a year ago I had a P0432 intermittely pop up, I recently just installed new pre cats. I drove around a couple days, and then took a road trip and it seemed to have solve the code. Bank 2 cat had nothing left when...

Replacing the shift tower seals on my 04 tj with an nv3550. Removed the 4 bolts to take the tower off the top of the transmission. The shift lever where the two M6 bolts would go are completely shot. I am unable to thread a fastener to compress the spring. I do have a separate transmission that...

I have a nv3550 with a leaky shift tower, just got some seals (will do a review in another thready I posted) in and would like to get those in plus some fluid in before my next road trip, a week and a half away. Transmission is filled with redline mtl but for the life of me cannot find the left...

I have a very leaky shift tower in my nv3550. I have been looking for parts for awhile now and Just stumbled across these seals made by amp drivetrain. Anyone have any reviews on these? I am going to go ahead and order some as I hate to keep checking trans fluid level, and red line isn't getting...

I have a couple random jeep parts to clear out. Located in Ontario but can ship from Detroit (buyer pays shipping etc...) THe steering wheel covers, small bracket and canister looking thing are all $10 then pay for shipping (bracket and canister is the mount for the small part next to a cruise...

I have some rough country lift parts for sale. The shocks are from a 4" lift kit, rears have around 5k km on them and fronts about 20-25k km. I have all 8 adjustable arms, only 7 are pictured as I have to remove the last one from the jeep but am out with an injury for a little bit. I have all...

Earlier in the week I had a ball joint fail on me. Ordered up the spcier ball joints... Come to find out someone put a different style ball joint in before I owned the tj, with knurling. I was wondering what the best course of action is now ( I have seen the dimpling fix, can that be done and...

Went wheeling for the first time in awhile. The trails were flooded. Got into some nasty bog etc... Time to drive home no worries on the ride back (600km) except for a little bit of squeaking that sounded like TOB/ or some belt stuff. But no grinding or anything that worried me... Got home...

Yukon dana 30 carrier, 3.73 and up with good condition spiders, carrier has around 20k km). The carrier got pulled because I upgraded to an e locker. Can ship on buyers expense. Its cheaper if I drive over to the states and ship, hence why I put Michigan.

I have 2 rear tj rubi lockers for sale, as parts. The one locker was used and worked fine until pulled, had a small chirp on left turns, not sure if that was bearing or because I used the internals from one to put in it. It also had a decent amount of shavings when pulled. The other locker has...

Long story short I ended up using the ARB compressor I got that I intially was going to sell... I am wondering if anyone has converted the 5 pin switch over to a 2 pin toggle switch? I have the Isolation switch hooked up to a 2 pin toggle switch, but for some reason cannot figure it out for the...

In the process of swapping my open dana 30 carrier to a locker. After a regear how much should the backlash open up if any at all, I am measuring around 14.5-15 thousandths which seems like a lot. It has run flawlessly for the last 20k km. Thinking I should slap it back together, and go no front...

I have a like new ARB ckma12 air compressor for sale, comes with arb air chuck. Bought the harness from someone else for the sale, but it was never used. I am in Ontario, will be crossing over to the states in the very near future to pick up my front locker. So can ship it out then to make...

Thinking about swapping my 231 for a 241OR and have been off and on about it for awhile, so I always keep an eye out in my area. I found a case and the guy I am talking to said it had no issues when pulled... My issue with the case is he swapped the flange yolk with a standard yolk, and I know...

Like the title states the blind spot detection in my mirror will not go off, easiest fix?... LOL

Looking for an Eaton 19977-010, or arb rd117. Also looking for a dana 30 3.73 and up locker as well. Thanks!

I am trying to dial in my tj's front-end pinion angle. For some reason no matter what I do my axle wants to roll forward creating a pinion angle that is to high. Was Swapping my fixed lowers... The jeep now has Uppers disconnected, the trackbar is disconnected, and the sway bars as well as the...

Hey all, I am rebuilding my factory Rubi rear locker today. When I get to reassembling the locker what should I torque the t50 bolts to and the allen ones? Any suggestions while I am in there? I have the new-to-me factory rear all taken apart and has great internals, should I be using those...

Looking to purchase a rear rubicon locker/ limited slip gears. Thanks!