Search results

I bought one of these kits and installed it many years ago. I'm thinking I would like to put the wiring back to stock but it had me cut and splice/wires hanging....I really don't even know how to go back without reversing the instructions. Thanks

I need to work on this area today for my rust repair. Does anyone have a nice clear photo of what it is supposed to look like? Thanks!

Suppose I was to take the body off the frame... I would need to disconnect the AC lines... Obviously the refrigerant would have to be removed and replaced eventually but would you need to cap off the lines to prevent moisture from entering the system and is there a preferred method of capping...

I got rid of my original one a long time ago. Picked up a used one but the material that is covering it seems different than my memory. I thought I remember it being a more cloth-like material such as my roll bars pads but this one is sort of a thin vinyl covering. Any insights?

Can anyone tell me the differences? I see different part numbers for my 2002 auto vs manual. Was going to possibly buy a tilt column for mine from a part out Jeep but mine is an auto trans and the partout is a manual trans.

I've always been interested in installing the factory sub and console in my 2002. I recently pulled out the required crossbody wiring harness and console from same model year donor Jeep. The 2002 sub has a 6-way connector. I think the 2003+ has a 12 way connector with two differences being: 1...

I'm thinking maybe the front face comes off somehow and that is how you get to the terminals and bus bars? Anyone know how to do it?

I was browsing through maintenance procedures on my DD Ford. For engine vibration symptoms, one of the steps in the troubleshooting is to neutralize the mounts which involves loosening all the bolts on motor and transmission mounts, driving the vehicle forward and backward 2-4ft, and...

Was thinking about buying a set I recently saw on marketplace... How do these hold up over time? Do they need to be polished? I think the rims are steel but I don't think they are chrome which is sort of confusing. Do they get rusty? Rims like this:

I'm wondering if they are supposed to go on so the rubber flap is on the inside of the grill and the plastic pushpins facing toward the outside? Any help? Just when I thought I was making some good progress getting everything back together...I bet it all needs to come apart again

Anyone know where this goes? I took the grille apart but I can't figure out how to put this piece back in. Might not even be for the grille, not really sure.

Nothing comes up when I do a search. For rear drum brakes. Only shows front bleeder screws available. Anyone know a secret brand or part number?

Is that normal? My Jeep has been sitting for a long time (6 months+). I thought I would crack the bleeders and let the lines gravity bleed but it doesn't seem like that would work with the proportioning valve connections being dry. Should that whole thing be filled with fluid? I guess I'm just...

So I'll be painting my entire Jeep soon...I ordered some silver metallic paint from Summit Racing. I started spraying some of it today on my new fenders and it is very sparkly. This is a hilarious thing to happen because I never liked factory metallic paint and I was thinking about going with a...

Bought some half doors last year. My half door thread Keep finding little surprises... Door hinge pin seized Small crack in interior panel Door keeper strap loops being bent in on both sides (fixed that with some wood and a pry bar) Latest discovery is the outside driver door handle doesn't...

Anybody have some sitting around? Seems like various different companies make these now. I am wondering is someone can measure the OD of the bushing for me? I replaced mine with the Delrin bushings a few years ago. I think it was when only one guy was selling them online. I couldn't get one of...

No idea how the heck this happened - I'm the original owner. Usually I'm pretty handy with a sledge hammer, some boards, and a bottle jack. But I'm sort of stumped how to try and fix this one. That whole area seems pretty sturdy and I don't think it's just the flange.

I'm doing a full repaint on my Jeep and pretty much decided on removing all the hinges and cleaning up the rust before I paint. I got the windshield screws loosened but I read something about a plate in there that can come out of place? Any more details or photos or anything? Is there anywhere...

I discovered my factory tailgate has some rust on the bottom seam. I hit it with the needle scaler. Seems pretty solid. Think I should sandblast and keep it or get a knockoff replacement tailgate? Will be getting a complete paintjob either way.

Couple weeks ago I picked up some Canyons in bad shape. Peeling clearcoat and lots of corrosion. I hit it with a syphon sandblaster with coal slag and it cleaned up the corroded parts wonderfully but the clearcoat was too tough and it wouldn't take it off. I later attacked the clearcoat with...