Search results

  1. csaxj3

    SOLD 2004 Jeep LJ turn-key build

    2004 Jeep Wrangler Unlimited, LJ Williamson Co. TN Vin: 1J4FA49S44P803453 Mileage: 109,104 4.0 Inline Six 42RLE automatic Dana 30 front axle Dana 44 rear axle All work was performed by Millcreek Overland / Automotive in Nolensville, TN. Receipts of all work can be presented. There is no rust...
  2. csaxj3

    Tennessee Bartac seat covers and tomken winch plate

    Grey Bartac seat covers, receiver hitch, and Tomken winch plate in the greater Nashville area. $200 for everything.
  3. csaxj3

    I'm at an impasse with my build direction

    So a year later into the LJ project I've made some progress on what I considered my "build sheet". The few times it's been out on dirt it has done extremely well - notably the 3 day Red Clay Rally this past fall. At the end of the day I'd wager the Rally will be the hardest this is pushed on an...
  4. csaxj3

    SOLD JCR half doors

    Got a set of JCR half doors that were used once, going in a different direction. Nashville area, no shipping at this time. $300. SOLD! I will get pics up this weekend.
  5. csaxj3

    Help me baseline my LJ for the Red Clay Rally

    A buddy and I have entered into the Red Clay Rally which takes place this October in the Southeast. Several friends have done this over the previous years and said I'd be crazy not to do it. This timed perfectly with the acquisition of the 04 LJ this past February, as I wanted to build a nice...
  6. csaxj3

    Which tie rod setup should I go with?

    Got a little jingle in the pocket and wanted to upgrade the ole tie rod setup 1.) get the Currie setup 2.) get the ZJ setup 3.) get the savvy setup 4.) get something I don’t know about teach me the ways and spend my money!
  7. csaxj3

    WTB: WTB: OEM LJ Hardtop - TN

    Looking for an OEM LJ hardtop in decent / good shape. Located in Nashville area and will drive a bit if needed.
  8. csaxj3

    Pick my gears!

    Time to order gears, as in the next 24 hours! 04 LJ, 42RLE, 3.73 gears, 33x10.5 ( no plans on 35's at this time). Need to order gears and a powertrax for Dana 30. 4.88 or 5.13? Goal is to be able to cruise 2+ hours to wheeling spots for the weekend and around town during the week. In addition...
  9. csaxj3

    What psi for 33x10.5 tires?

    The maxxis 33x10.5’s are my first C load and wanted to see what PSI you guys are running on road and when you air down? use to E loads on the Toyota’s.
  10. csaxj3

    04 LJ Build Thread

    Figured I'd start one of these! Picked up my LJ in mid February after looking for several months. It checked all the boxes for me: Southern, stock, and no rust. Was hoping for a Rubicon model, but realized for the cost delta I could build up an equally capable LJ. That said I'd love the 44's...
  11. csaxj3

    Do I need a dropped pitman arm for a 4 inch Savvy lift?

    Swung by the shop this morning to check on the LJ and drop off a nutsert kit for them. shop suggested I need a drop pitman arm for the build. yes / no? school me.
  12. csaxj3

    Blue sea disconnect mounting location

    Any suggestions where to mount the blue sea disconnect for my winch? good mounting point , aftermarket bracket, etc?
  13. csaxj3

    What is the typical Savvy wait time?

    Ordered my 4" lift on 2/19. Tried to follow up this week to see if there is an ETA on it shipping out, as it's all I'm waiting on to get this build into gear. I understand that Savvy is hard to get a hold of / has a lead time - what is the usual wait - 4-8 weeks? Their phone went to...
  14. csaxj3

    Suspension time (budget is 2k)

    Time to get the build going and pick up a new lift. Budget is $2k for the lift - (lift only, no labor). Currently set on the JKS JSPEC 3" kit (here), would add rear trackbar and steering stabilizer to the package. Vehicle is stock 04 LJ I picked up a couple of weeks ago, goal is to run...
  15. csaxj3

    Tennessee Middle TN - Nashville area shop recommendations

    Looking for shop recommendations around the greater Nashville area. Would prefer independent shop vs 4WP. Thank you!