Search results

Here ya go 👇🏼

Y’all still recommending Timken for the Axle bearing/ hub assembly? Thanks

Ok gentlemen. I need 2 new steering knuckles. Ideally I’d get Mopar but that’s going to be around $1,000. So, not happening. Chipped off some really good chunks of metal. Thoughts on OMIX or Crown? Or others I’m not suggesting. Please spare me the lecture on spending money for good parts. I...

Why would the PO of my Jeep only put a body lift on the driver and passenger side? Aren’t body lifts typically both sides along with front and rear? Never had one so I don’t know. Any reason why someone would do this? Thanks

Which was does the gasket face. Blue towards engine or blue towards water pump? Thanks

Few days ago, went out to the garage, and saw some coolant on the floor, more than just a few drops. Teresa, back as far as I could, was guessing it was the water pump. Today I take off the applicable parts and as I’m looking at the water pump, I no longer think it’s the weep hole or the pump...

Ok guys, there is a backorder on the Mopar thermostat with no timeline on the books. 2000 Wrangler Sport 4.0....what do you all recommend since I cant get the OE part Thank you

Ok guys. Front of oil pan, antifreeze leak. Left quite a mess earlier. Thoughts? Water pump? You guys are always amazing at this stuff. Thanks

Thoughts on running without it? Anyone have an opinion? Thanks

Not sure if I’m allowed to do this but can we sell things on here? Anyone?

Definitely a chirping noise when turning either direction. Lifted up both driver and passenger sides individually, checked for play in the wheel front to back and it’s solid. While each individual wheel was up I spun them both, no noises at all. Any thoughts? Thank you guys.

Ok so I know where the brake master cylinder is but what is this? Says it takes DOT 3. Dumb question probably but I have no clue. 2000 TJ SPORT

Hey guys so I am installing a RC 2.5 inch lift on my 2000 TJ. Why on earth is the drivers side coil bowing like this (see pics) I swapped sides and no matter what coil I put in it bows. As you can see the pig tail is in the split. CA’s (bottom) are loosened. And even when I put the tire back...

Alright guys, 2000 TJ, just installed the Rough Country 2.5 inch lift. However, the drivers side coil is bowing towards the front of the vehicle. Tires are back on and when I set it down it bows out as you can see. Even hitting that whole metal housing area. Sway bar is still disconnecting...

2000 Sport, Dana 35 rear Should I use brake cleaner on the gears to clean it. Thoughts? Thanks guys!

Ok guys here’s the deal. A few months I ago I removed the bump stop cap on the passenger side no issues. Bolt came right out as far as I recall. Today I’m trying to remove the drivers side of my 2000 TJ and it seems as if I’ve unthreaded it completely yet the bolt will not come out. It just...

Hey guys. So I removed the pin and when the pin came off the “cap” fell off too. Not sure what it’s called but you see the pic. I’m trying to remove the axel nut so I can get to the U joint. However when I put my 12 point 36mm socket on the nut (pic 2) the axel just spins when I try to loosen...

My question is this. My U-Joints are pretty rusted, my steering knuckle not so bad. But, can I safely spray these two things with some fluid film? Thank you guys!

Ok guys so I’m a newbie at this and before y’all laugh at me remember we all started from knowing nothing. First 3 pics is the steering knuckle on my 2000 TJ. Can this be salvaged? Wire wheel, rust oleum and some fluid film? Would that work? 4th pic is the yoke and U Joint (I think) Same...

Hey guys please watch the attached video it will give you my questions. I guess what I’m asking is should I replace these things or, will some rustoleum and fluid film do the job for the next several years. Thank you so much for all of your help.