Search results

The 2024 Wrangler refresh has been announced and what peaked my interest the most is the Dana 44 rear is now full float and looks like they are using a unit bearing.

Just curious for front stretches. How far forward can the front track bar be moved before running into issues? What are some of the issues that come up when moving it forward to make room for uptravel?

I’ve seen it mentioned here a few times, has anyone done a rear stretch and moved the factory frame arches to center the axle with the stretch in wheelbase? Would love to see some pics and any real world observations on the up travel gains and limitations.

The 555ci big block with the Whipple super charger sounds amazing.

This sucker is so clean underneath. Ends today. https://bringatrailer.com/listing/2004-jeep-wrangler-57/#comments-anchor The underside is unreal, no stupid spray paint or coatings.

https://bringatrailer.com/listing/2002-jeep-wrangler-29/ I was surprised by the milage and how clean it actually is underneath. This one was very well kept.

https://bringatrailer.com/listing/2006-jeep-wrangler-75/

As the title says, I'm looking for pictures of TJ's/LJ's with Poison Spyder Customs "Defender" front fenders, Highline, no highline, doesn't matter. https://shop.poisonspyder.com/TJ-LJ-Defenders-Negative-Flares-Steel-p/14-02-050.htm

I purchased a YJ Wrangler with swapped aftermarket axles, 40's, beadlocks, flat fenders, custom bumpers, coil overs, frame mods, and everything else that goes with 40's. Not 24 hours after purchasing it, I had just filled it with gas and of course someone pulls out in front of me causing a...

Can anyone explain the pros and cons that exist between a 2.0” coil over and a 2.5” coil over? Or rather the difference between the 2.0 and 2.5 inch coil overs? And has anyone been able to run the 2.5’s using full width axles (69.5” WMS) and sunk-in frame mounts? Is there enough room for...

Looking for a low milage rust free 03+ TJ or LJ I know some of you are really good at finding these gems… @Starrs

https://www.ebay.com/itm/1999-Jeep-Wrangler-Sahara-/353645428614?mkcid=1&mkrid=711-53200-19255-0&siteid=0&customid=link&campid=5337789113&toolid=20001&mkevt=1

Looking to print an Atlas 2 transfer case. I’m located in the southeastern United States, so local would be ideal. If there is a printing service that can ship, I would have no issue with going that route either.

Advanced Adapters sells cable shifters for their cases. Are they worth their price? Is there anything better? Advanced Adapters Cable Shifter Kit: https://www.advanceadapters.com/products/303009--cable-shifter-for-an-atlas/

I’m sure most are aware of engine mock up products. They are made of plastic and used to check engine placement, exhaust clearance, and suspension clearance for 4 wheel drives. Makes it really easy to pull, check everything, place back in, check adjustments, and pull again. Does anyone know if...

As the title says, looking for OEM or aftermarket (Timken) Ford 05-12 Superduty unit bearings that have been re drilled to 8x6.5 and utlizes a screw in 9/16-18 wheel stud. Anyone know a company that would accommodate or stock such a thing other than Spidertrax. Spidertrax 05+ unit bearing only...

The powers that be at Ford dropped a pretty impressive bomb in regards to their upcoming Bronco release. During the lunch hour at KoH yesterday in front of the fans as well as virtually to all the live streamers, Ford officially announced they will be offering a Ford Bronco that is KoH ready...

Machined weldable tabs for 3/16 hard lines, drilled and tapped. *Cost will be updated when the machine shop gets back to my supplier. Could have a batch going through the machine shop in the next few days. Looking at ordering 100, 200, or 300 pieces. With the higher probability being 100 pieces.

Anyone have any recommendations on an accurate and reliable scale to use with parts in and around the garage? Looking to spend $200 or less.