Search results

  1. Blaine 06LJR

    Opinions on these Mammoth wheels?

    I love them. These are 35x12.5" on 15x8 mammoths with 1.25" titan hubcentric spacers. I went with mammoth over Quadratec because of the available colored center caps.
  2. Blaine 06LJR

    Currie Currectlync install issue

    Your caster looks off. Your axle looks rotated forward. That would cause your problem but I don't know how you can drive down the road like that!
  3. Blaine 06LJR

    Revolution shafts won’t fit rubicon

    Yes! I have these axles on my Rubicon. I had the same issue. Not sure about yours but my bolts are still the factory flange bolts with the smaller 12 point head. I had to install and torque bolts, mark the part of the bolt flange that was hitting, remove bolts one at a time, then Dremel off...
  4. Blaine 06LJR

    What should I paint my Dana 44 with?

    I use Rustolium rust reformer on everything! brush off loose dirt and rust and spray away. Its cheap easy and stops rust.
  5. Blaine 06LJR

    Thank you for recommending Rancho RS5000X shocks!

    I hear a lot of people rave about these shocks. I just bought some cheap Quadratec nitros about a year ago right after I bought my Jeep and didn't know any better. Are the Ranchos so good that i should consider upgrading my 1y/o quardratec shocks now?
  6. Blaine 06LJR

    Reservoir shocks: Why do I see so many people running them?

    It's ironic that the Amazon add at the bottom of this page is for Fox and Bistein reservoir shocks
  7. Blaine 06LJR

    Rear bumper with carrier

    I have a Rock Hard and LOVE IT! I bought a Fishbone first and it was a POS that was basically uninstallable because of all the poor design and quality control issues. Quadratec let me return the Fishbone for the Rock Hard and I've been greatful ever since.
  8. Blaine 06LJR

    Currie Control Arms

    I just did a full Currie double adjustable lift install alone in my garage on, don't worry too much. *Drilling out the Upper CA mounts was much easier and quicker than I expected. Even on the axle side sleeves. (I had springs removed) *I installed the jam nut end of the LCA's toward the frame...
  9. Blaine 06LJR

    My automatic transmission is on its way out: 42RLE to NSG370 swap?

    I'm hoping to get one of these when mine goes. Which I think will be soon because my 42RLE does weird stuff all the time! http://www.atsdiesel.com/ats2/productdetail.asp?p=3069408272
  10. Blaine 06LJR

    RCV axles vs u-joint axles

    My revolutions did take a little Dremel creativity to get the u-joints in the shafts and allow the shafts to turn without hitting the flanges on the unit bearing flange bolts. This just proves to me that revolution made the shafts as beefy as they could and still fit. Don't let this deter you...
  11. Blaine 06LJR

    RCV axles vs u-joint axles

    I resently upgrade my front axles. (also upgraded rear but that's not what this is about) My choice came down to RCVs vs Revoltion American made axles. I felt the RCVs were all around better but are a little overkill for a tj rubi with stock drivetrain. Heck even the Revolution Axles are...
  12. Blaine 06LJR

    Free, cheap, & low cost mods for your Jeep Wrangler TJ

    For Rubicons my cheapest most effective mod to date is a bypass switch for the 4low locker permissive. I can now use my factory lockers in 4 hi or even 2wd. <$20 This is how you do it: http://www.wanderingtrail.com/Mods/TJLJmods/Locker_Defeat.htm