Search results

Hello, The Kicker amp has two connection options; RCA (low) and speaker (high). Since the factory head unit doesn't have RCA out, I connected it to the speaker cables supplying the factory amp/sub combo that came with my Jeep. I used the left and right front speaker cables...

So glad I read this thread! I had the same harsh rattle that seemed to come from the glove box, every time I hit a pothole. The hood support rod was popping out of the retainer clip and banging on the passenger grill support rod. Slipped some rubber tubing around the rod and that fixed it...

I just did this... - Tensioner: Mopar part 4854089AB. From Amazon as CharlesHS suggests, comes with the torx head bolt. I don't think it would be a good idea to substitute this bolt, as the head seems to have a taper for positioning/securing the unit. - Idler pulley: Mopar part 4854092...

Yes, plenty of solutions, but don't really want to add another key to my collection, thought the ignition keying option could work out. Probably an expensive cap with a trip the the locksmith though!

Ha, ha - South side maybe, but pretty quiet in the burbs. Not so much the stealing of gas, but more about discouraging sabotage.

Hi all, I'd like to get a locking gas cap, preferably utilizing the ignition key. Crown makes one... https://www.quadratec.com/products/15006_0012.htm?utm_source=bing&utm_medium=cpc&utm_campaign=shopping And so does Mopar... https://www.amazon.com/dp/B0049EJVRQ/?tag=wranglerorg-20...

Okay, set the LPF to 100 Hz, flattened the equalizer (media player and head unit) and adjusted gain - much better! Punchier bass, with less variation between tracks. Thanks @skrelnik !!

Speaker level input. Yes, adjusted gain as you mentioned. Any thoughts on the best low pass filter setting?

Have not upgraded the head unit, but sounds good enough for me. Supposed to output 200 W at 0.5 ohm, hence why I wired the DVCs in parallel, but that's peak and not RMS. Just wanted to tweak the settings in order to narrow the range of bass output between different tracks - if that makes sense?

Hello. At the recommendation of this forum, I upgraded my factory sub/amp with a Kicker 42PXA2001 amp and 43CWRT671 (1 ohm) sub. I wired the sub dual coils in parallel (0.5 ohm) and connected the amp input to the front speakers (that were supplying the factory amp). Everything is working and...

Not wear, but rust. On the outside and creeping under where the gasket seals.

Hi all. Decided to replace the valve cover gasket and vent grommets, as oil is coming out somewhere. After getting everything off, the cover is looking worse for wear. I could clean it up and paint it, but probably easier to replace it. It seems the Mopar part is discontinued and the only...

Finally got around to tightening them... Left side: Pushing the star wheel down expands the shoes. Right side: Pushing the star wheel up expands the shoes. I expanded them until it was difficult to turn the tire, then backed off by 4 notches on the star wheel. Parking brake now holds at 3...

Thanks for the explanation, makes sense now. Didn't realize there was a splined joint underneath. There's no need to pull apart, so no worries then.

Two halves? Do you mean disconnect what's under the boot (I assume a piston-type connection)?

Just realized my second question is a stupid one! But still wondering about need for reference marks.

Hi all. I removed the front prop shaft for easier exhaust/oil pan removal and didn't add reference marks (as per the service manual). Why are these marks needed? Looks to me that it wouldn't matter if the u-joint was installed in the original position or rotated by 180 degrees. Do the...

I'm replacing my rusted exhaust and wondered if it's worth recycling the cats. There are a few websites offering to buy them, but before getting a quote, I wondered if anyone here has experience, recommendations and example prices to share. BTW, its a stock 2006 exhaust with three(?) cats.

Probably original (14 years and 70K). Yeah, might replace.

This got me interested - check out this horror story... https://www.brewracingframes.com/safety-alert-brake-cleaner--phosgene-gas.html