Search results

You doing the work yourself? You could replace the whole AC system in parts from Rockauto for about $500-600. Compressed/drier ~300, condenser 70, evaporator 40, and $100-150 for all hoses and lines. Labor costs would be mechanic and location dependent.

I put it on with the pulley tool. I rented the puller and installer from autozone. I just couldn’t get it from turning to torque it to 80ftlbs. It kept turning, despite me putting it into first and reverse. Putting it into 5th gave me the resistance to torque it down. I’m relatively...

And thanks!!!! Saved me a ton of work pulling transmission to look for an error.

Huh. Well that’s wierd. That worked. Allowed me to tighten it to 80ftlbs without turning. Why is that??? I’m really confused. Im not much of a car guy - mostly just able to follow FSM.

It’s in 2H

Hi all, This is probably a stupid question. I just installed a reman engine in my 2000 4.0 manual. I went to tighten the vibration damper bolt, and so put the transmission in gear to hold it. However, when I go to tighten it I can still turn it. I thought the transmission would hold the...

Thanks! I didn’t have the parts catalog - I was trying to figure it out from the FSM which wasn’t clear. Thanks again super helpful!!

I got National SCE1295. It’s the bearing only. After doing some more research I “think” I need the one with the sleeve. Rockauto has the one you used, but it’s called “Manual trans; includes bearing sleeve repair kit”. I don’t know why the FSM doesn’t mention a sleeve, unless it’s just...

Hi all. Quick question. I have a 2000 TJ 4.0 with the NV 3550 transmission. I just bought a reman engine. When I look at my old crankshaft, it looks like the pilot bearing is in a sleeve installed in the outer, larger diameter recess. I bought a pilot bearing off rockauto, and it’s just...

For the front crankshaft seal, FSM calls for “perfect seal” on the outer lip. Can I use black RTV? Getting mixed answers when I search- some say use Aviation form-a-gasket, some say black RTV. Some say definitely don’t use black RTV. Anyone know acceptable substitute for “perfect seal”?

So the block is cracked. Someone local is selling a used Jasper with 43K miles on it out of a 2004 that was rear ended. From the research I’ve done, a 4.0 out of a 2004 should fit my 2000. Does anyone know anything I should look out for? Mine is the early 2000 with the federal emissions so...

Their price included all their parts. If I had them just do the machine work I’d buy the pistons and rings and bring to them. It sounds like the 2800 included upgraded pistons and some of their preferred parts, and the 2400 was an enginetech master rebuild kit.

I don’t think so - I just told them I’d buy a complete head online. I’m sure they would if I asked them. They seem to know what they are doing, and the online reviews are mostly positive. If you don’t think that’s high maybe I’ll have them do it all just to avoid me screwing something up...

Thanks all! Super helpful. This is my first time doing any internal engine work so 1) trying to not mess anything up and 2) trying to not look like an idiot with the machine shop. I called a local shop with good reviews, and they quoted me 2400-2800 for everything (depending on brand of...

Never mind. Just found some other posts with pics that look like mine with people calling it normal. Weird place to have a hole from casting, and it’s jagged like it blew out. O well, learned something tonight.

So tore it down and broke the piston skirt on #5. Didn’t look to bad, so I thought I might rebuild it. But when I took off the oil cover and removed the cam I noticed the hole in the block in the picture. It’s right above the cam behind the timing cover. I assume it’s not supposed to be...

Thanks all. I almost got it pulled so I’ll tear it apart and see what happened. Based on advice here I’m leaning towards rebuilding it myself. After the knock developed I drove it for a minute or two until it started to over heat. What’s the chance I cracked the block with whatever was...

Thanks. Sorry if this is a stupid question - trying to figure out what to ask the machine shop if I call around. If I rebuilt it myself how much does the machine shop typically do? Or what would you recommend asking them to do? Just prep, bore, and mill it? Or do they assemble the whole...

I’m not exactly sure - haven’t torn into it yet. I had a tick on cold start for about 2 weeks and thought was a lifter tick. It only occurred for about 5 minutes after starting. Then last week it turned into a loud knock, engine was running real rough, and then started overheating. Pulled...

2000 4.0 and the engine finally bit it. Looking to replace with a reman - have read all the posts and it seems no company is free from a few bad reviews. Had a question from those with more experience in replacing their engine - Titan engines offers the following upgrades - are any of them...