Recent content by Tinnitus_Z

It was this piece, also attached the original Sketchup created .stl of the part I 3D printed. That .stl model did work for roughly 2.5 years but I will remake it and print more with a higher filament density (corn based PLA). Had issues uploading pictures earlier. 3D printed part that broke...

Gave it another look, took out the center console covering the stick and the airbag computer to get a better angle. That small arm/bracket for the lower blend door broke again, it was still connected but wasn't turning the door. Replaced it with my spare one and will remodel that arm/bracket...

Thanks all for the replies, I will double check the vacuum lines going into the heater box and recheck the lower actuator arms once I have time this coming week.

It has been a while since I last posted on here. I have looked at previous posts about the climate control only blowing out of the feet vents and some fixes that people have gotten, such as HVAC and engine bay vacuum leaks and broken actuators. However, I have checked all of my vacuum lines in...

Hello again, I've been getting the P0340 and P1391 codes recently. Last week the starter solenoid went out, and I had to buy a whole new starter with it included since they don't sell the solenoid separately. After I replaced the starter and cleared the codes, only the P0340 code came back, and...

The only filament allowed to use at the 3D printers at my library is corn based PLA. Online it says it starts to melt around 170 and the temp of the printer has to be 190 before printing. I don’t know how hot it will get in there since my heat doesn’t fully work anyways. Temperature coming out...

Update: I have installed the bracket/arm piece and it fully works and turns the door when changing the air control between blower and defrost. That STL file that I posted, and if you 3D printed it, will work in place of that arm piece if it was broken like mine. It did have trouble at first...

I've tried my best to recreate the bracket/arm in Sketchup from scratch and 3D printed it. Here are the pictures of the actual piece with a ton of glue, and the 3D printed piece. This did take a while and the file is the best resulting 3D print. Here is the STL file, although it may need to be...

Alright, I'll go check while doing the quick center to side turns instead of the long full side to side turns. As for the tire balance, I am most likely getting new rims and tires in the next few months so hopefully all four wheels shouuld be balanced.

Hello again, here's a video of my front-end track bar in question. When I turn my wheels to the right, there is a loud popping noise coming from the passenger side. Took this video and noticed that the track bar is moving in the bracket and "popping" when I turn to the right, and this is very...

I found an old photo of when I got the pieces out. The part on the left breaks into 2 pieces, and I've lost some tiny fragments that were holding everything together. I'll have to wait until I bring it back to where I currently live before I can Jerry rig it. Would you recommend just a coarse...

I have not fixed it yet. I’ve contacted the Jeep dealerships part specialist on October 5th and still haven’t gotten a reply. Probably isn’t even worth trying to talk to the dealership though. I’m currently away from home at college and when I get back for thanksgiving break, I’ll grab the...

Hello, sorry if this is similar to my previous post, but I decided to take some pictures of what I am talking about with the heat blend door. I have verified that all the actuators and electrical motors work, all the vacuum lines are good and there are no leaks, but I cannot get defrost working...

So the second picture shows the arm that broke. One side is supposed to clip into the metal piece of the actuator, and the other part of that plastic arm plugs into the hole in the heat box in the last picture. (The hole directly to the right of the metal piece in the last picture to be more...

Hello all, after taking apart my dashboard to find the issue with my heat, I accidentally broke the arm that connects to the bottom driver side HVAC actuator. I have a 2002 4.0L if that is needed to help. I have fixed my heating issue and I now get 125-130 degrees when the heat is on...