What did you do to your TJ today?

MikeE024 said:
I’d be game to do this as well if that would be ok. We just gotta remember that each setup requires different spacing.
Click to expand...
Attached are the files that I sent to Custom 3D Fab ([email protected]). I paid $42 shipped for 4 of the spacers. That included modifying the file (attached) to the dimensions that I needed (2.5"). That company was GREAT to work with. Their communication was beyond great. If I ever need anything 3D printed again, I will go to them first.

This is where I got my center dash switch panel as well. His stuff is top notch.
 

Attachments

  • 4in Snubber.zip
    15.3 KB · Views: 23
  • jeep-tj-spare-tire-bumper-spacer-model_files.zip
    48.9 KB · Views: 19
  • Like
  • USA Proud
Reactions: KimsJeep, MikeE024 and Danarch
mjonesjr84 said:
What was your justification for spending that much on a Dana 30? I'm debating spending money on my axles or looking for a decent set of Rubicon axles as a base platform.
Click to expand...

The Rubicon 44s aren't really better than a Dana 30 with better shafts.

The main benefit is availability of deeper gears.

Check the below link.

Dana 30 vs Dana 44
 
  • Like
  • Wow
Reactions: John Cooper, ColoJeep and mjonesjr84
RangerTJ said:
The Rubicon 44s aren't really better than a Dana 30 with better shafts.

The main benefit is availability of deeper gears.

Check the below link.

Dana 30 vs Dana 44
Click to expand...
So keep the 30 but upgrade the carrier and axles. What about the rear? Swap in a 8.8 or upgrade the 35? I don't plan on absolutely beating the TJ, but would like to regear to get back some power. The 33's and 3.73's aren't bad, but could be better. I do want lockers front and rear.
 
mjonesjr84 said:
Attached are the files that I sent to Custom 3D Fab ([email protected]). I paid $42 shipped for 4 of the spacers. That included modifying the file (attached) to the dimensions that I needed (2.5"). That company was GREAT to work with. Their communication was beyond great. If I ever need anything 3D printed again, I will go to them first.

This is where I got my center dash switch panel as well. His stuff is top notch.
Click to expand...

You da man!
 
  • Like
Reactions: mjonesjr84
mjonesjr84 said:
The 33's and 3.73's aren't bad, but could be better.
Click to expand...

Just my opinion… I just went from 3.07’s to 4.11’s in my TJ on 33’s with a 32rh and if I had to do over, I would go 3.73’s… I love the power that the 4.11’s gives but on the highway the RPMs are screaming and I’ve lost mpg’s… The 3.73’s would not be as loud as the 4.11’s and you would get better MPG‘s… Can’t believe there would be that much difference between 3.73’s and 4.11’s…
 
  • Like
Reactions: Ocho and mjonesjr84
Ordered Baja MTZ tires while receiving notification that I passed the AZ bar exam. Just sharing bc I’m happy and thankful (and mostly relieved!) Got a 280, which is good for all UBE states. Passage rate was 46% wtf!

IMG_2063.jpeg



IMG_2060.jpeg


Now for the July CA exam bc I like to torture myself.
 
Last edited:
  • Like
  • USA Proud
Reactions: JoseA, LakeBeard, LJtobey and 16 others
mjonesjr84 said:
Attached are the files that I sent to Custom 3D Fab ([email protected]). I paid $42 shipped for 4 of the spacers. That included modifying the file (attached) to the dimensions that I needed (2.5"). That company was GREAT to work with. Their communication was beyond great. If I ever need anything 3D printed again, I will go to them first.

This is where I got my center dash switch panel as well. His stuff is top notch.
Click to expand...

Thanks man!
 
  • Like
Reactions: mjonesjr84
MikeE024 said:
Ordered Baja MTZ tires while receiving notification that I passed the bar exam. Just sharing bc I’m happy and thankful. Got a 280 so I’m good in all UBE states. Passage rate was 46% wtf.

View attachment 518143


View attachment 518146

Now for the July CA exam bc I like to torture myself.
Click to expand...

Congratulations on passing.

You know why lawyers wear ties?
 
  • Haha
Reactions: MikeE024 and mjonesjr84
MikeE024 said:
Ordered Baja MTZ tires while receiving notification that I passed the AZ bar exam. Just sharing bc I’m happy and thankful (and mostly relieved!) Got a 280, which is good for all UBE states. Passage rate was 46% wtf!

View attachment 518143


View attachment 518146

Now for the July CA exam bc I like to torture myself.
Click to expand...

Congrats dude! I remember when we were chatting last year and you were in lecture hell. Glad you got it done.
 
  • USA Proud
Reactions: MikeE024
mjonesjr84 said:
Attached are the files that I sent to Custom 3D Fab ([email protected]). I paid $42 shipped for 4 of the spacers. That included modifying the file (attached) to the dimensions that I needed (2.5"). That company was GREAT to work with. Their communication was beyond great. If I ever need anything 3D printed again, I will go to them first.

This is where I got my center dash switch panel as well. His stuff is top notch.
Click to expand...

Windows (and 7-Zip) says the files are invalid. :unsure: Andy
 
  • Like
Reactions: mjonesjr84
red02tj said:
Congrats dude! I remember when we were chatting last year and you were in lecture hell. Glad you got it done.
Click to expand...

Thanks man :) Yea that was pretty rough six classes took things to the edge.

AndyA said:
@MikeE024 I can print the parts for you (once I get working zip files) and you can come and collect them. Let me know. Andy
Click to expand...

Woah that would be amazing man! And an excuse to meet you. :)
 
  • Like
Reactions: mjonesjr84
Top Bottom
Back