Search results

Hi all, just replaced my TJs rear disc brakes with new pads and rotors and I noticed even after break in I’m getting the burnt brake smell. After driving I checked caliper temperatures and they were both around 390F whereas the fronts were at 110F. I’m guessing that for some reason there is...

Hi all, Picture attached but due to a shortage of spicer 709644x ball joints, went with the Yukon ones, but to my surprise the lower joint had a Zerk fitting…in a test fit with just sliding the axle in, it looks like it either just barely clears or just barely hits, so my question is do I...

Selling set of 5 D load rated BFG KO2s 37x12.5R17 with 14/32nds of original 15.5/32nds tread left, less than 10k miles…went smaller to make family happier with jeep 🙁. DC area (Bethesda MD).

Selling set of 5 D load rated BFG KO2s 37x12.5R17 with 14/32nds of original 15.5/32nds tread left, less than 10k miles…went smaller to make family happier with jeep 🙁. DC area (Bethesda MD).

Ok, initial search didn’t find this, but after replacing the parking brake equalizer bracket, and adjusting them, I noticed that the driver side wheel is locked tight with no movement when engaged, but passenger side is allowing just a little movement back and forth of the wheel before stopping...

Hi all, hoping I can get help…checked a few of the suggested threads but not all so apologize if missed this… Replaced fuel tank with a genright unit, but in pulling the sending unit, in the bottom of the old tank was a rectangular what looked like filter material, but it doesn’t actually seem...

Hi all, don’t believe all parts of this have been discussed, but redirect if I missed something in my search. Took jeep in for alignment with Firestone and they suggested new unit bearings…which is very early. Took it home, raised it and tested, and a lot of play in the drivers side but none...

So I had another thought on the usefulness of the hub lockers…with the atlas 4 speed, I can’t flat tow without disconnecting the drive shafts, which isn’t hard, but with the locking hubs I should be able to leave the front shaft connnected, saving time and I also think just wear and tear on the...

Plus, I’m not a hard driver, but every now and then I might be prone to doing something stupid….

Yep, sounds like not worth it especially for the cost! Think I’ll just find a bit more room to carry a spare unit bearing and outer shaft…if anything breaks upstream of those, just disconnect/remove problem and live with 2wd… Thanks!

Then not sure they are really worth it to me…love the idea of a weak point in a system (electrical engineer in me) to protect the more delicate and costly/complex components to replace.

I’m looking at getting the Yukon locking hubs for my TJ, my primary reason would be for the ‘fuse’ component…would love to have that as the most likely (no guarantees) failure point in the event of a high stress load. Read this thread, but hoping more people might chime in and comment if the...

Yes, great point! Driving in 4th only shows you the difference at high end, not acceleration and starting from a stop…so agree. Since I drive mine almost as a daily driver spring - fall (criteria, warmer than 25 morning, 55 afternoon, less than 40% chance of rain), I see a lot of flat highway...

The ratio of 4th to 5th is similar (although far from exact) to the ratio of 4.88 to 4.10s, so driving in fourth is like driving in 5th for 4.10s. For me I think the ideal is 4.56. Now I do have the atlas 4 speed, so wheeling I have an incredible selection of ratios with a doubly low around a...

Just a note…I’m the black sheep of the forum as everyone tells me everything I’ve done is wrong, yet the Jeep drives well to me (and as a former Jeep engineer said…it drives better than he expected 🤣🤣🤣)

I know everyone is saying 4.11s are low for 33s… but I run 4.11s on 37s (lightweight set with aluminum wheels) and while I know I use fourth for any power, I have no lugging issues and have enough power in 5th gear for small hills and enough to accelerate decently on flat ground. I have 4.0...

Anyone know a belly up kit that would work with an Atlas 4speed? When I first got the four speed I also got a belly up kit and was told it would fit…but it didn’t due to the extra length on the four speed. The shop said they could try cutting it down, but ended up sticking with the stock...

I am curious, is there an acceptable amount to center within…I know previously my center was far off and it was still driveable, but with my last set of changes my center on the axles are within an eighth to quarter inch (takes a bit more effort to get a precise measurement). What is an...

Damn, wrote a reply and couldn’t recall password, but now properly logged in so hope this helps! First, there are far more out there with practical experience than I, but will give you what I found. My current lift is sitting at 3ish inches and I found my front pinion to driveline angle was...

I do plan to eventually replace clutch, debating if I want to try it in my single car garage over the winter…just worried about the weight of the tranny, otherwise the process doesn’t look to complex…he said before dropping the transmission…