Recent content by Edgar Marton

Hi guys, Another little problem, hopefully you can help. Jeep runs well when it runs. When starting it runs very rough (15 seconds, revs start at 500 and slowly work their way up to 1000 rpm and then stay constant) - looks like the engine is not getting the right mixture to start. Throttle body...

Does anyone know this spare part? A friend of mine would like to sell this spare part - it is said to come from a 1998 TJ ... I have a TJ myself - but this spare part is completely unknown to me. Thanks a lot Edgar from Hungary

Hello, again a question from Hungary with a request for help. A year ago complete converter renewal with automatic transmission renewal. Overhaul Master Kit. Since one month very sporadically a speed-dependent noise between converter and engine outlet - where the black rubber sleeve sits (Output...

I have the same problem. I want to make a metal rod - what is the length in cm? Sorry, come from Europe.... the diameter is not more than 6 mm, right ? Thanks and greetings from Budapest, Edgar

Maybe the same theme... When I step on the brake and release, I have a clicking noise in the selector lever from the ATG (when releasing....). This problem is unfortunately not 100% reproducible and only occurs in the "D" position. When touching the selector lever, the noise can also be felt -...

Where is NSS switch physically located ? I haven't found anything yet - but I'm sure I've been looking in the wrong place. Can someone please post a picture of the NSS in the installed state ? Thanks from Hungary, Edgar

Hello mots, Still working. No rust. No leak - all good. I'll leave it that way now - the winters are getting warmer and warmer in Europe - that's enough for heating. I have expanded the bypass in the meantime. Bypass Heater Core - new heating

aaahhh, right - 14 and 15 are Pins and not separatly relays. My fault. Easy. Can I use the connection between these two pins to build a push start button (with wires inside the cabin and so on...)? Should actually work ... BTW: Forget German jeep forums (I'm also a member) - people only complain...

Hello @qslim, Which pins have to be bridged (from 14 to 10)? I am stranded with my 1999 TJ - ignition problem (actuator brocken,as has often been discussed) - I now have to do ignition bypass with a push start button, otherwise my wife will no longer have to drive the jeep 500 meters to the...

Unfortunately my ingnition cylinder lock broke in a parking lot and the TJ can no longer be started - all electrics work, everything is ok, but the starter motor does not start. How can I start the Jeep TJ in emergency mode so that I can at least get home? Cable bridges? Best Regards, Edgar...

Hello, another question frum the hungarian US-Jeep Fan.... On one side the strap of the hood latch are broken. I would happily replace that with the Daystar KJ09146BK replacement kit. How can I remove the inner retaining pin in the rubber strap??? Unfortunately fhis is not plastic that I can...

Got the answer from ARP Hi Edgar, 146-2801is for a flywheel (manual transmission) 146-2901 is for a flexplate (automatic transmission) Best regards, Zac Kimball Technical Support Automotive Racing Products, Inc. 800-826-3045 ARP-bolts.com

ARP 146-2801(UHL 0.875˝) or ARP 146-2901(UHL 0.500˝) for automatic transmission ? 32rh ARP 146-2901 ARP 146-2801

Hi Jerry, I was expecting you to answer. You are the heart and soul of this forum. Really. No, I mean this bolts: Maybe: https://www.rockauto.com/en/moreinfo.php?pk=10307396&pt=8556&jsn=266 But there is no picture .... I mean this Number 24 on Your list? AND the rubber seal ? I only found...

Jeep Wrangler TJ 4.0 Sahara, Forrest Green, 230.000 km build 04/1999 TRANSMISSION - 3-SPD. AUTOMATIC, 32RH (DGG) Maschine: 4.0L POWER TECH I-6 (ERH) Hello, I need a little help from Hungary. I have to change the flexplate and need 5 (if I remember well) new bolts. I'm registered with Rockauto...