Search results

My jeep is making a rythmic noise from the front driveshaft if I go 70mph. Sounds like I am coasting back and forth over rumble strips but not quite that loud. I know it is the front driveshaft because I took it off and the noise went away. So I rebuilt all the u joints and center ball joint...

So I have an LS swap 2003 TJ. But I am using the Jeop computer to run the gauges and lights. My CEL is on all the time based on this. My question is focused on the “check gauges” light. Does anyone know what triggers this light? When I start my jeep, the CEL is on (like always) and then a...

First I did not select the RC 4” lift. It came on the Jeep when I bought it. It does have the drop pitman arm and it has the drop bracket for the track bar. I installed the ZJ upgrade steering components, did a garage alignment (3/16” farther apart in rear), and see no slop when doing a...

Jeep JK Dana 44. IIRC there needs to be a pin where I placed the safety wire (for the pic)? I don’t see it in the drain pan. Did a mechanic just decide it was Friday and put the cover on?

2003 TJ but axle was swapped to Dana 44, by someone else. Can anyone tell me what parking brake cable I need for a Dana 44 w disc brakes? I am guessing 2003 Rubicon brake cables would be correct?

2003 TJ with 5.3L swap. Running GM NV3500 5 speed to NP231J. Previous owner had clocked the transfer case to transmission my slotting the transmission end. (Think drilled hole that broke off the outer portion). I am at work or I’d have a pic I have a replacement transmission to install but I am...

I think it is but want to be sure… Like to get a second key but 99.9% sure I have SKIM and it has not been bypassed.

So I have LED headlights that seem to be Sunpie brands (can’t verify as they came on the Jeep at time of purchase). The issue I have is when I turn on my high beams, they act more like fog lights (they are lower than my low beams). I checked the wiring and I don’t have the wires flipped, they...

1999 TJ Just had the dash out and reconnected everything. At the control I do have burn connections at the 5 wire plug and the 3 wire plug. I reattached the wires of the 3 plug individually but got nothing. I pulled the resistor from passenger side kick panel and looks new? Tested grounds on...

1999 Wrangler TJ. This is my 16th Jeep so if you don’t like my mods/price please move on and keep your comments to yourself. 1999 Jeep Wrangler TJ 4.0L 5 speed 6” long arm lift 34” BFG KO2 ($2000) Eaton E lockers front/rear, 4.56 gears New brakes, calipers, lines front and rear Banks exhaust...

I am in the process of taking a YJ 2.5L down to the block and adding all the TJ components back on. I have a small engine stabilizer, does anyone know if this is for the TJ or just older models? Can’t find it in the TJ service manual

I get all spun around with the two letter models. Will a 4.0L 1998 Grand Cherokee engine drop in a 1999 TJ 4.0L. if any thing would need changed, what would that be? Getting ready to Buy, so all help appreciated. I found this but want to ask specifically so I know for sure.

99 TJ with every problem you can think of...been fixing them as I discover them. changed thermostat and water pump, noted some leaking coolant this morning and concluded this freeze plug is leaking. Looks like a rubber bolt in style? Anyone confirm this? Any thing special with removal? Loosen...

Seem the new Spicer 706944X ball joint may be too small? I was able to slide it in by hand almost to its final spot? Upper is about the same too. Do I need a different ball joint or is this common?

I have a 99 TJ that has a swapped 4.0 L engine, from what I do not know. The water pump pulley has the following number stamped on it. 53002907J It seems the bolt pattern of my pulley is larger than normal TJ‘s. But I have gone to several Napa’s and advanced auto‘s and I am striking out. I’ve...

99 TJ 6” long arm lift, has a front drop track bar mount on the frame and a drop pitman arm. I believe this to be the correct setup due to the drop track bar frame mount. ZJ steering upgrade BUT I am getting some rubbing at the axle track bar mount. any ideas? I bought all new steering linkage...

I need to either regear my front axle to 4.56 or just put a Dana 30/35 with 4.10s on the Jeep. I know very well the 4.56 gears are awesome for some, but I am afraid they may be a bit low for me. BUT, I would like to know how much the following would be worth so I can make a better decision...

Sold TRADE FOR FULL DOORS? Teal green Half hard doors Tan interior From a 1997 SE Fairfield PA 17320 $450 No shipping, Looking for local sale

PO monkeyed with the wiring and ran this green/pink stripe wire to a circuit board. I want to remove all the extra wiring and want to put this back where it should go. It comes up with the main feed at the PDC. I think the PDC but I don’t see a short wire that would indicate such. any ideas?