MrTeak

Supporting Member

TJ Enthusiast 52 From New Jersey

Joined: Sep 19, 2020

Last seen: Wednesday at 3:48 PM

Latest activity Postings Images About

- MrTeak replied to the thread Shock recommendations.
  
  When shopping for shocks do you include the body lift as part of the lift. (2.5in lift and 1.25 body lift) do you shop shocks for 3.5in...
  
  Saturday at 5:48 PM
- MrTeak reacted to AndyG's post in the thread What did you do to your TJ today? with Like.
  
  Headed to test a new rig...
  
  Saturday at 5:05 PM
- MrTeak reacted to AndyG's post in the thread What did you do to your TJ today? with Like.
  
  Rock lights for underhood- waterproof switch ordered-
  
  Saturday at 5:02 PM
- MrTeak reacted to TheBoogieman's post in the thread What did you do to your TJ today? with Like.
  
  "According to the CDC Trusted Source the two ticks that can cause Lyme disease include the blacklegged tick and the western blacklegged...
  
  Saturday at 4:59 PM
- MrTeak replied to the thread Eaton E-locker Question.
  
  So after 15 minutes of fiddling with the pins and plug I got them to seat properly and locked in and boom the locker works.
  
  Saturday at 9:52 AM
- MrTeak replied to the thread Eaton E-locker Question.
  
  So I tried jacking up the rear wheels and try to engage it by turning the driveshaft by hand and no luck, so I started to chase the wire...
  
  Apr 19, 2024
- MrTeak reacted to freedom_in_4low's post in the thread Eaton E-locker Question with Like.
  
  It makes sense if you think about it and watch that video. If the carrier needs to rotate relative to the housing then you need to turn...
  
  Apr 19, 2024
- MrTeak reacted to macleanflood's post in the thread Eaton E-locker Question with Like.
  
  You can also measure ohms across the two pins...you should have resistance...I can try and lookup the values. But yes...you really have...
  
  Apr 19, 2024
- MrTeak reacted to freedom_in_4low's post in the thread Eaton E-locker Question with Like.
  
  I think I checked mine with both wheels off the ground, in neutral, and I spun the driveshaft by hand until it locked in. When I did...
  
  Apr 19, 2024
- MrTeak reacted to OldBuzzard's post in the thread Eaton E-locker Question with Like.
  
  I had the identical experience, spun a wheel considerably farther than I thought it needed to lock, but it didn't. Turning the...
  
  Apr 19, 2024
- MrTeak posted the thread Eaton E-locker Question in TJ General Discussion.
  
  I had the shop install my Super 35 and Eaton elocker and they left the plug hanging on the axle and I wired up the locker. I looked at a...
  
  Apr 18, 2024
- MrTeak replied to the thread Is this bracket broken?.
  
  Yes, I’ve read that they snap off pretty easy. I will rock the engine and check.
  
  Apr 2, 2024
- MrTeak reacted to JEEPCJTJ's post in the thread Is this bracket broken? with Like.
  
  Nothing looks broke to me. As for looking into it further Getting someone fairly strong to rock the engine side to side while you watch...
  
  Apr 2, 2024
- MrTeak replied to the thread Is this bracket broken?.
  
  The jeep rides fine, I don’t hear any weird noises or sounds, I just noticed that while I was there and it didn’t look right. So on that...
  
  Apr 1, 2024
- MrTeak reacted to P man's post in the thread Is this bracket broken? with Like.
  
  Brown dog makes brackets just for this problem..I personally don't care for his mounts but maybe you could use the plates and use...
  
  Apr 1, 2024
Show older items
Loading…
Loading…
Loading…

Top Bottom

Back

Search

Search

MrTeak

Find content

Latest activity Postings Images About