bearing

  1. SACressionnie

    Pinion Nut Slightly Over Torqued

    So, I'm rebuilding my Dana 35 rear end and I just installed new pinion bearings. Put the pinion nut on and started tightening to set the crush sleeve. I got super close to the low end of the spec (15 in. Lbs) on the rotational force and decided to go another bump or two (not with impact). Now...
  2. DWR

    What seals do I need for a Dana 44 with 35 spline axle shafts?

    Long story short, when I re-geared my jeep and noticed I had aftermarket axles in my rear dana44 I didn’t count the splines like a dummy… Turns out the prior owner upgraded to 35spline axles (according to the person I was paying to replace the seals as I simply couldn’t be bothered lol)… so the...
  3. H

    Chirping from input shaft/pilot bearing?

    Hello All, I've got a 2003 Wrangler. 4.0 5spd. I just recently had the throw-out bearing go. Had a shop replace it along with a new clutch. I asked them to install a new pilot bearing and input shaft bearing as well, but a new noise I am getting now makes me think they did not replace them, or...
  4. freedom_in_4low

    Oklahoma OEM axle shafts front and rear

    I just upgraded to chromoly. front Dana 30 27 spline OEM axle shafts. about 5k miles on sealed Spicer 5-760x u-joints. Ran with 32's and an open diff. Includes ABS tone rings but you don't need ABS to use them. The middle part of the passenger side shaft is cleaner because it's been in an 80s...
  5. Jt223

    Axle pulled out

    What did I do wrong? 3 days ago I replaced me rear axle seal and bearing. Last night as I was pulling into a parking spot at work my axle came undone. The retainer plate basically pulled off everything that was pressed on my axle. Left it all in the tube. I pressed everything on the correct...
  6. dom.robles

    Squeaking noise after off-roading

    I got some snow in the local mountains a few days back and I took my 99 2.5 up to play around in. It's a pretty mellow dirt road but there were a few puddles and some dust at the bottom where it was dry. When i hit the pavement i started hearing a squeaking noise which i had a good bit of...
  7. M

    Possible Input Shaft Bearing Issue

    Good morning, all. I'm trying to diagnose a new sound (as if there weren't plenty of sounds already) coming from my 1999 Jeep Wrangler 4.0 TJ. A few days ago I started hearing this almost asynchronous grinding/whining sound when I have the vehicle in gear and giving it gas. It would...
  8. DominicWilbrink

    Dana 35: Correct Wheel Seal Installation?

    Does anyone know if I have this seal installed correctly? This is a Dana 35 on my 2001 Jeep Wrangler TJ. This started as a brake job and then morphed into a bunch of work on the rear axle. When I removed the old brake drum on the drivers side I found the brakes coated in oil. I replaced the...
  9. Rob F

    Bearing noise on decel

    Hey all. I need some opinions. I have an 03 Sahara, NV3550 5 spd and 231 J t-case. I have developed over the last 2 months a very loud bearing noise when I let off throttle, in all gears. Even coasting in neutral it is there. If I throw the t-case in neutral when coasting, it goes away...
  10. B

    AC Bearing Replacement...What Brand?

    The bearing is shot on my A/c compressor and I need to replace it. Ive looked at getting a whole new compressor but i am 17 and hardly ever use the A/C so i would really like to just replace the bearing.http://www.szr-bearing.com/product.html I know this is a common problem and ive searched and...