driveshaft

So I'm in the process of doing a transmission swap on my 97 SE. I'm going to the NV3550 with the NV341OR but for now I'm keeping my stock axels. Can I use the driveshafts from the Rubi that pair with the NV341OR or will I need to order something special from Adams or elsewhere? If I remember...

Brand New Never Used - Center of u-joint to end of slip is 5 3/4", Shaft is about 14 1/4" from center to center of the u-joints. Rear part (yoke) is 3 1/2" wide. Shaft is 15 5/8" from end of u-joint cap to end of opposite end cap. Machined part of sliding yoke is 2.5" deep. Not for Unlimited...

I am preparing to purchase more parts, imagine that? Anyway, I going to replace the clutch and while I'm there I want to install a SYE on my NP231 (2000 4.0L manual).I'm being told I need to purchase a CUSTOM MADE drive shaft? Looking online, I see lots of CV drive shafts and none of them are...

Hi All, So I'm in the market for a new front driveshaft for my 1999 Jeep 2.5l 4cyl. On all the websites I can only find front driveshafts for a 4.0 I know that the auto ds and the manual ds are different but are the 4.0 and 2.5 ds different. If anyone knows if the driveshafts are interchangeable...

Hoping someone can help out here. I bought a new Adams rear driveshaft for my 2003 rubicon and found my flange is a bit different from most options I could find online. All holes on the flange are NOT threaded and the holes on my drive shaft are threaded. Anyone seen this before?

98 TJ 4L, 3sp, w/ 2.5 in lift. Everything was good with the lift, no driveline vibrations. Then I added the following: CURRIE FRONT TRACK BAR CURRIE REAR TRACK BAR CURRIE ADJUSTABLE UPPER AND LOWER CONTROL ARMS, FRONT AND REAR MOOG UPPER and LOWER BALL JOINTS SLIP YOKE ELIMINATOR CONSTANT...

I have heard nothing but good things about JB conversions. Noticed they offer a super short SYE that looks outstanding which allows for an even longer driveshaft. Having a longer driveshaft is far less likely to have have vibrations due less angle to reach the rear axle. It should also have...

I had finished up a week in Moab, wheelin' with some friends, and I noticed that the front drive shaft was squeaking. It was not constant, but rather an on again, off again kind of thing. After getting home, I decided it was time to pull the drive shaft and take a look. I had not felt any...

So I need expertise I recently broke my drive shaft driving up a gravel road. Prior to that and now with my new shaft my jeep slams when I let out clutch in first gear. I noticed that the end play at the pinion yoke was about a quarter turn. Can someone tell me if this is excessive, is that my...

I understand that my 05 Rubicon uses a 1330 u-joint on the front driveshaft, is that correct? If so, what is the spicer part number for a replacement u-joint? Preferably an upgraded one if possible. 5-760X, or will that not fit?

Okay, so I had my rear driveshaft angle at about 16 degrees and the rear pinion was at about 15 degrees when I completed the my Currie suspension install. I never noticed any vibrations until today because I hadn't been at highway speeds until now. Anyways, I noticed over 40 mph it definitely...

Last time I removed the springs I used spring compressors. This time I am installing my Currie 4" lift and decided I'd rather avoid spring compressors and just get the springs out by lowering the axle. Well, it seems that even with everything disconnected the only way to get the axle to drop...

I'm not sure if the title explains what I am trying to figure out, but why is it that a double cardan driveshaft is sometimes referred to as a 'CV' driveshaft? I was under the impression that a CV driveshaft was similar to the type of CV joint found on say an RCV axle or most modern day...

I'm installing my Currie 4" lift. In the process of doing so I need to adjust my pinion angles. I know what the rear angle is supposed to look like with the Tom Wood double cardan driveshaft I'll be installing. However, I am wondering if anyone has a photo of what my stock front driveshaft...

Driveline Geometry 101 O.K. so now you've done it. You put that lift in your vehicle or changed the engine, transmission or transfer case or differential maybe all of the above and now your go anywhere four wheel drive baby rides like a out of balance washing machine. Or now that you've got...

I'm going to be replacing my 2.5" OME lift with a 4" Currie short arm lift, complete with fully adjustable Currie control arms including double adjustable uppers. In addition to that I have a1.25" BL and 1" MML. I realize my stock drive shafts will not cut it any longer and I need to have...

What type of driveshaft is the stock TJ Rubicon rear driveshaft? Is it CV, u-joint, etc.? I'm new to this so I was just curious since I heard I need a CV style for a tummy tuck but wasn't sure if my stock one would work or not.